Agisoft Metashape
Agisoft Metashape => Feature Requests => Topic started by: RobiOne on September 21, 2012, 04:59:25 PM
-
Could it be possible to add compatibility with 6 degree of freedom controller like the 3dconnexion spacenavigator?
It improves a lot the 3d usability and the interaction feeling (i use it routinely on other 3d softwares)
Roberto
-
I support this request. I use 3DConnexion Space Navigator with other software. It would be more efficient to be able to do translations and rotations of the display without having to switch from editing.
-
Agisoft, any further developments in supporting 3Dconnexion devices?
-
I too would like this request as I use a 3d mouse.
-
I would also love support for 3dconnexion i Photoscan! It feels so limited without it after having worked with it in for instance Rhino.
-
Hello,
I just acquired a 3D mouse (from 3dconnexion) in order to work faster on my complex 3D models.
Unfortunately PS does not seam to have support for this type of mouses. Is this correct? Will there be an implementation soon?
Or is there a way around to activate the mouse within PS?
Best regards.
-
http://www.3dconnexion.com/products/spacenavigator.html
-
Big +1... Would be really useful. It's frustrating not being able to use mine.
-
It would be very usefull and precise to navigate inside the viewport with that 3D mouse. Ability to disable the handle visibility then would be too.
http://www.3dconnexion.eu/index.php?id=26
Sdk available here: http://www.3dconnexion.eu/service/software-developer.html
-
yes! this would ne a nice feature!
-
http://www.3dconnexion.com/products/spacemouse/spacenavigator.html
-
I too require the use of a 3d mouse. Any update on this Agisoft team?? ??? ??
-
Have anyone seen any answer to this topic? I didnĀ“t find anything..
-
Hello laakti,
3D connexion devices are supported by Agisoft Viewer only at the moment.
-
Big + for this post
-
I too have a 3Dconnexion space mouse and it fails to work properly in the software.
This is a real shame as it speeds up the workflow and usability of the software immensely.
Are there some settings I should be aware of to make this work? At present I have all of the control settings to control the 3D model, but only zoom works and very poorly at that.
I have the same problem in the latest version 1.2.6 as well as the WIP 1.3
Thanks in advance for looking into this.
-
Big + for me too
-
I have been facing the same problem and wish for a quick solution and support for 3Dconnexion hardware.
-
http://www.3dconnexion.com/products/spacemouse/spacenavigator.html
(http://www.3dconnexion.com/fileadmin/templates/images/assets_sn/SN_front.jpg)
-
Big + for this. So sad my space mouse doesn't work yet.
-
It seems no one of Agisoft is reading this... Navigating in your 3d environment is a real pain without a 3d mouse!
Turning the object with the mouse and then switching back to selection tools etc. is extreeemly annoying, also due to the fact that your 3D model movement is surprisingly unintuitive.
-
Hello,
We are checking all forum threads regularly.
In the version 1.4 the support for 3D Connexion SpaceMouse (http://"http://www.3dconnexion.ru/products/spacemouse.html") and Stealth 3D Mouse Controller (http://"http://www.stealth3dmouse.com/index.php/products/products") would be implemented.
-
+1
Looking forward to version 1.4
-
Pre-release of the version 1.4 is available: http://www.agisoft.com/forum/index.php?topic=7730.0
Any feedback related to the 3D controller devices is appreciated in the pre-release thread.
-
Hi,
I have a Sthealth 3D mouse modell S1-Z. The connection is by USB port and not by COM1 port. COM1 port is the only one i can choose in Agisoft. How i can configure it?
Regards,
Luis
-
Hello Luis,
After you connect Stealth Mouse with the computer using USB you should go to the Device Manager, locate USB serial converter and in it's properties enable VCP (Virtual COM Port), then re-connect controller to the same USB port and again in the Device Manager you'll see COM3 port. After that you should be able to select COM3 in PhotoScan preferences window for the controller.
-
Hello all,
Additional information related to the 3D controller support. In the pre-release update of the version 1.4.0 (build 5420) it is possible to invert the navigation directions and adjust the sensitivity in the Navigation tab of PhotoScan Preferences window.
-
Hello @,
this is really great news that Spacemouse support is going to be implemented. I have some older Spacemouse Classic, equipped with serial connector (9-pin). I installed Spacemouse X-Windows driver v4.65 at my Linux box (SuSE Leap42.3) It is still working but requires some special tricks:-) 3D-Cube is working, but when I enable Spacemouse support in PhotoScan, it doesn't work.
SpaceMouse Classic is no longer supported by 3DConnexion as far as I know but you find them at Ebay for some EUR, I got mine for 5 EUR. That's good for the low budget.
@Agisoft: will you stay restless until Spacemouse support is seamless working and even my old Spacemouse Classic? Would be a greatful feature.
-
Hello Alexey,
It is realy great to get 3Dconnexion space mouse support for the stereoscopic measurements but we couldnt connect the USB version of the Space mouse. I understand the software only supports serial connection on com ports for now. Will there be an improvement regarding USB connected devices especialy for 3Dconnexion space mouse? :)
Thanks in advance.
-
Hello pantatpantat,
I've provided the instruction above:
After you connect Stealth Mouse with the computer using USB you should go to the Device Manager, locate USB serial converter and in it's properties enable VCP (Virtual COM Port), then re-connect controller to the same USB port and again in the Device Manager you'll see COM3 port. After that you should be able to select COM3 in PhotoScan preferences window for the controller.
-
Hello again.
I am pretty sure that there is no "usb serial converter" driver in device manager also there is no usb to serial converter hardware connected to my pc. I dont know any way of bridging usb and serial ports some how for 3Dconnextion Space Mouse. I think this is the situation.
Thanks for your quick response.
-
Hello pantatpantat,
3DConnexion device should work "out of box", if their driver is installed. So no need to enable it in the Preferences.
I thought that you were speaking about the Stealth 3D Mouse controller, sorry for confusion.
-
Hi there.
I have the same situation With my 3DConnexion SpaceMouse Enterprice. No functionallity in Agisoft, only zoom in and out. Have anyone at all managed to make this work, and what functions are supported?
-
Hello
Can you help me to configure stealth 3D Mouse to use it with Photoscan ?
Thank you.