1
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Feature Requests / Report and estimations.
« on: July 04, 2013, 07:20:24 AM »
Hello,
It will be grat to have possibility of editing report before PDF construction.
Ea.:
1. To add "tittle" line on first page (also header/footer fields)
2. Rtf field "description" for few words about project (p?ace, time, equipment, etc)
Or -> save report to editable format as rtf, doc, etc.
Second is time estimations: after loading photos -> rough time estimations of all possibilities of project - time of alignment on diff. resolutions, model creations, etc.
Best,
Marek
It will be grat to have possibility of editing report before PDF construction.
Ea.:
1. To add "tittle" line on first page (also header/footer fields)
2. Rtf field "description" for few words about project (p?ace, time, equipment, etc)
Or -> save report to editable format as rtf, doc, etc.
Second is time estimations: after loading photos -> rough time estimations of all possibilities of project - time of alignment on diff. resolutions, model creations, etc.
Best,
Marek
3
General / Re: Hardware request of information
« on: June 28, 2013, 08:12:44 PM »
Main purpose is small ortophoto - 0.5 - 5 km2, photos from UAV with resolution 5cm/px or better, flight level 50-150m above ground, 12-18 MPx.
Photos - every 2-3 seconds during entire flight, so probably 100-1000 photos in one set. Actual - Canon SX260HS 12 MPx - picture jpeg 4000x3000 px)
Goal is speed (possibility of produce ortophotomap and digital elevation model on-site, just after flight).
Application - university lab for training crisis management situations (forest fires, flodings, etc) - delivery actual data for local GIS system used by students.
Photos - every 2-3 seconds during entire flight, so probably 100-1000 photos in one set. Actual - Canon SX260HS 12 MPx - picture jpeg 4000x3000 px)
Goal is speed (possibility of produce ortophotomap and digital elevation model on-site, just after flight).
Application - university lab for training crisis management situations (forest fires, flodings, etc) - delivery actual data for local GIS system used by students.
4
General / Re: Hardware request of information
« on: June 28, 2013, 03:31:18 PM »
Hello Wishgranter and Alexey,
Thanks for reply.
Purpose is only for PhotoScan.
So fot the similar price as C2075 I have offer for 1 x GTX TITAN 6GB or 2 x ASUS Radeon or 3 x AMD Radeon HD7970. All new with warranty.
What will be better 1xTitan or 2xASUS / AMD 7970?
M.
Thanks for reply.
Purpose is only for PhotoScan.
So fot the similar price as C2075 I have offer for 1 x GTX TITAN 6GB or 2 x ASUS Radeon or 3 x AMD Radeon HD7970. All new with warranty.
What will be better 1xTitan or 2xASUS / AMD 7970?
M.
5
General / Re: Hardware request of information
« on: June 28, 2013, 01:32:12 PM »
@Mohabon:
Did you (or anyone) tested Tesla C-2075 in real with PhotoScan?
I have option to buy one from second-hand for 1.2k$ , so any info will be great help to take decision.
Did you (or anyone) tested Tesla C-2075 in real with PhotoScan?
I have option to buy one from second-hand for 1.2k$ , so any info will be great help to take decision.
9
General / Re: New to ortophoto
« on: May 30, 2013, 11:19:14 AM »
For above work camera lens was uncalibrated.
Calibration with Lens program just done, and tryied again to process photos with 0.9.1 software in demo mode. When finish - will post few screenshots.
Anyway - next week should buy full version....
Here is link to short move on YT from field: http://youtu.be/I6dLvf14vwg
Attached scren - point cloud 0.9.1, cam lens calibrated
Calibration with Lens program just done, and tryied again to process photos with 0.9.1 software in demo mode. When finish - will post few screenshots.
Anyway - next week should buy full version....
Here is link to short move on YT from field: http://youtu.be/I6dLvf14vwg
Attached scren - point cloud 0.9.1, cam lens calibrated
10
General / New to ortophoto
« on: May 29, 2013, 05:04:09 PM »
Hello All,
My first works with demo version.
58 photos, Canon SX230HS, 1/800 s, ISO 100, my own construction UAV, flight level - 100 m above ground.
All done as described in tutorial: First run tutorial:
Orthophoto and DEM Generation with Agisoft PhotoScan Pro 0.8.5(without Ground Control Points)
Comments and suggestions - welcome
My first works with demo version.
58 photos, Canon SX230HS, 1/800 s, ISO 100, my own construction UAV, flight level - 100 m above ground.
All done as described in tutorial: First run tutorial:
Orthophoto and DEM Generation with Agisoft PhotoScan Pro 0.8.5(without Ground Control Points)
Comments and suggestions - welcome
Pages: [1]
