Forum

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - LouFlat12

Pages: [1]
1
General / Re: Photos missing information
« on: December 02, 2015, 07:37:12 PM »
I don't have them in a separate text file, I think they were included in the image EXIF.

2
General / Photos missing information
« on: December 02, 2015, 06:56:37 PM »
hello there,

not sure if I've done anything wrong in the workflow but some of my photos in the cameras pane aren't showing any information i.e. longitude, latitude etc.

This means I am having trouble placing my ground control points. I have a feeling it might be due to problems on the UAV but not sure if there is anything I can do to get around this. :'( :-[ :(

anything possible I can do?

thanks

3
General / Re: Signifcant error in total error to do with cameras
« on: November 12, 2015, 02:18:12 PM »
ive tried using british national grid and the error problem still occurs

4
General / Re: Signifcant error in total error to do with cameras
« on: November 12, 2015, 02:04:45 PM »
Looking at my camera information the lontitude seems very off, this could possibly be why the error is so large, is there anyway to solve this?

5
General / Re: Signifcant error in total error to do with cameras
« on: November 12, 2015, 01:58:27 PM »
Hi,

I've been using WGS 84 (EPSG::4326), my study site is in Northumberland, UK, I thought this was correct?

6
General / Re: Signifcant error in total error to do with cameras
« on: November 12, 2015, 01:54:02 PM »
Hi sorry,

Very new to this so not sure of all the information to give

Thanks

7
General / Signifcant error in total error to do with cameras
« on: November 12, 2015, 01:36:40 PM »
Hi there,


I am reading the report for the DEM that I am generating - I have 2 problems, the total error for the camera position is rather large, is there anyway I have done anything wrong within this project to cause this or is this correct? Also my projected DEM seems to suggest that elevation is continuous and doesn't seem to make much sense,, is there anything I can do about this also?

Thanks
Lou

8
General / Re: Problem with Orthophoto
« on: November 09, 2015, 01:41:35 PM »
Hi, I think I found my problem, when the computer brokedown effectively the images although they say that they are there, they have been damaged so will not load properly

9
General / Problem with Orthophoto
« on: November 09, 2015, 12:53:52 PM »
I had an orthophoto but unfortunately due to computer issues lost it, when I tried to go back to re-export the orthophoto it keeps coming up that a lot of my photos are missing and then if i try to export it nothing exports - not sure where I am going wrong?


thanks

10
General / Re: Unable to export Orthophoto
« on: October 27, 2015, 01:46:11 PM »
Ive managed to do it thankyou!!

11
General / Re: Unable to export Orthophoto
« on: October 27, 2015, 01:43:40 PM »
I thought that I had but I'm not sure if it wont let me export the orthophoto?

Louise

12
General / Unable to export Orthophoto
« on: October 27, 2015, 01:38:27 PM »
Hey there,


I have followed all the steps in the beginners guide to create a DEM but at the last two steps I have having trouble. When I go export the orthophoto it will not let me change the projection type to geographic and I'm not sure why? this is the projection I need to use.

Thanks

13
General / Re: Bounding boc problem
« on: October 26, 2015, 06:15:21 PM »
Thanks Alexey!

Was starting to panic there!

14
General / Bounding boc problem
« on: October 26, 2015, 06:01:10 PM »
Hi there

I am trying to make a DEM and have followed all the steps on the beginners guide, however I am not sure how but I seem to have messed up the bounding box, it no longer contains my points/camera shots, the bounding box seems not fully contain the information. I was wondering if there was a way to realign the bounding box?

Thanks

Pages: [1]