Forum

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - kiteman

Pages: [1] 2 3 ... 5
1
General / Re: Detect markers
« on: November 21, 2023, 06:29:09 PM »
Thank you very much!

2
General / Re: Detect markers
« on: November 21, 2023, 05:35:48 PM »
It's Works! But not for marker detected from Metashape. Why?

3
General / Re: Detect markers
« on: November 21, 2023, 05:32:49 PM »
Nooo....   :( now Work :) !! Thanks for patience

4
General / Re: Detect markers
« on: November 21, 2023, 05:27:43 PM »
Sorry, don't work. I don't Know where I wrong.  no active cell

5
General / Re: Detect markers
« on: November 21, 2023, 04:53:43 PM »
Hi Alexey,

Thanks for the explanation, but it doesn’t work.. even if I double click.. the cells won’t activate and I can’t enter xyz data.

6
General / Re: Detect markers
« on: November 21, 2023, 01:08:55 PM »
I think the problem is white flags, how can i convert it?

7
General / Detect markers
« on: November 21, 2023, 10:44:26 AM »
Hello everybody!

I'm learning to use metashape markers.
 I detected it , with :  tools - markers- detect markers, but the markers are blocked , I cannot enter information about xyz   ( see screenshot) . How can I activate them?

8
General / markers in the new version 2.0.1
« on: May 11, 2023, 05:05:01 PM »
Good evening everyone,

 Is it normal, that in the new version of Metashape, the flags of the markers are white? If I remember correctly, in the old version, they were blue

9
General / Re: Why this?
« on: January 28, 2020, 04:15:58 PM »
adjusted screen

10
General / Re: Why this?
« on: January 28, 2020, 04:15:20 PM »
Here initial screen

11
General / Why this?
« on: January 28, 2020, 01:51:39 PM »
Hi,
I have to create orthophotos from a series of cores.
the cores are inside a box shaped like a 1 meter long parellelepiped.
the point cloud of the box and the cardboard appears deformed by a curvature. why does this happen?
overlap of about 75%.



devo creare ortofoto di una serie di carotaggi.
i carotaggi sono all'interno di una scatola a forma di parellelepipedo di 1 metro di lunghezza.
la nuvola di punti della scatola e del cartaggio appaiono deformate da una curvatura. perchè accade questo?
sovrapposizione di circa il 75%.

12
General / how to create a point of origin?
« on: July 23, 2014, 01:00:55 PM »

I am photographing the surface of a series of concrete blocks in 3D, one by one.
How do I create a common origin for all models, with Agisoft?

I constructed a frame where emplace concrete brick, and then all the blocks are in the same position.

I would like to orient the surfaces of all the blocks in the same way between them, and give a zero point to the cloud of points (for example, the angle at the top left).

Is it possible? and if so, how?
thank you very much Stefano

13
General / Re: Camera Calibration Method & Parameters
« on: July 01, 2013, 01:01:00 PM »
very interesting! Could you explain better how to make this your idea?

14
General / Re: Problem with merged chunk
« on: April 23, 2013, 06:44:14 PM »
I tried to optimize, and after merging chunk error has risen to 97, while the georeferencing has worsened to 1.8 m

15
General / Re: Problem with merged chunk
« on: April 23, 2013, 06:35:54 PM »
I  just merged using the fact that they are already referenced in the same coordinate system.
Now i try to optimize.

Pages: [1] 2 3 ... 5