Forum

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Marek

Pages: [1]
1
General / Re: New to ortophoto
« on: July 04, 2013, 04:53:40 PM »

2
Feature Requests / Report and estimations.
« on: July 04, 2013, 07:20:24 AM »
Hello,

It will be grat to have possibility of editing report before PDF construction.
Ea.:
1. To add "tittle" line on first page (also header/footer fields)
2. Rtf field "description" for few words about project (p?ace, time, equipment, etc)
Or -> save report to editable format as rtf, doc, etc.

Second is time estimations: after loading photos -> rough time estimations of all possibilities of project - time of alignment on diff. resolutions, model creations, etc.

Best,

Marek

3
General / Re: Hardware request of information
« on: June 28, 2013, 08:12:44 PM »
Main purpose is small ortophoto - 0.5 - 5 km2, photos from UAV with resolution 5cm/px or better, flight level 50-150m above ground, 12-18 MPx.

Photos - every 2-3 seconds during entire flight, so probably 100-1000 photos in one set. Actual - Canon SX260HS 12 MPx - picture jpeg 4000x3000 px)

Goal is speed (possibility of produce ortophotomap and digital elevation model on-site, just after flight).

Application - university lab for training crisis management situations (forest fires, flodings, etc) - delivery actual data for local GIS system used by students.


4
General / Re: Hardware request of information
« on: June 28, 2013, 03:31:18 PM »
Hello Wishgranter and Alexey,
Thanks for reply.
Purpose is only for PhotoScan.

So fot the similar price as C2075 I have offer for 1 x GTX TITAN 6GB or 2 x ASUS Radeon or 3 x AMD  Radeon HD7970. All new with warranty.

What will be better 1xTitan or 2xASUS / AMD 7970?


M.

5
General / Re: Hardware request of information
« on: June 28, 2013, 01:32:12 PM »
@Mohabon:
Did you (or anyone) tested Tesla C-2075 in real with PhotoScan?
I have option to buy one from second-hand for 1.2k$ , so any info will be great help to take decision.


6
General / Re: New to ortophoto
« on: May 30, 2013, 07:35:44 PM »
cd

7
General / Re: New to ortophoto
« on: May 30, 2013, 07:34:45 PM »
cd

8
General / Re: New to ortophoto
« on: May 30, 2013, 07:34:20 PM »
Groups splited. Now from 0.9.1

9
General / Re: New to ortophoto
« on: May 30, 2013, 11:19:14 AM »
For above work camera lens was uncalibrated.
Calibration with Lens program just done, and tryied again to process photos with 0.9.1 software in demo mode. When finish - will post few screenshots.
Anyway - next week should buy full version.... :)

Here is link to short move on YT from field: http://youtu.be/I6dLvf14vwg

Attached scren - point cloud 0.9.1, cam lens calibrated

10
General / New to ortophoto
« on: May 29, 2013, 05:04:09 PM »
Hello All,
My first works with demo version.
58 photos, Canon SX230HS, 1/800 s, ISO 100, my own construction UAV, flight level - 100 m above ground.
All done as described in tutorial: First run tutorial:

Orthophoto and DEM Generation with Agisoft PhotoScan Pro 0.8.5(without Ground Control Points)


Comments and suggestions -  welcome  :D



Pages: [1]