Forum

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Sebas80

Pages: [1] 2 3
1
Feature Requests / Re: A tool to "link" together aligned chunks
« on: May 27, 2016, 01:06:47 PM »
Up....no answer?

2
Feature Requests / A tool to "link" together aligned chunks
« on: March 17, 2016, 07:06:04 PM »
Hello everyone,
if I have one chunk with known coordinates markers, and one or more other chunks aligned to the reference one with point based alignment method, if I replace the markers' coordinates with those of another local coord. system, I need to realign all the other chunks to have also these in the new reference system. That's frustrating  :-\. May you implement something to "link" the selected aligned chunks?

3
Feature Requests / Re: Ortho at given resolution
« on: March 16, 2016, 12:33:07 PM »
-

4
Hello,
Up to the version 1.1.0, when I scaled the model with a scale bar applied on two points, I usually exported the model by using "current view" projection plane, or "markers" projection plane, but I could insert also the pixel size.
From version 1.1.6 on (and so even on 1.2.3 version), I could just indicate the pixel size in such condition. Could you please fix it?
Thank you.

5
Still present in the 1.2.3 version.
May you fix it?
THank you.

6
Bug Reports / Re: Dense cloud manual editing issue.
« on: December 15, 2015, 11:43:37 PM »
Overall, this seems like a dodgy workflow at best :o

You could either duplicate your chunk before you start doing your edits, or save to psz and do your thing there

I cannot figure out how this could help me.
Let say I duplicate the chunk, and what I can do after that? By having a lot of points is not so easy to remove the outliers.
Most cloud point editing software allow to isolate a portion of the cloud and let you work on this particular, as many outliers, when you work with points, may be unvisible due to the presence of other point behind that. With agisoft I cannot do that, and this is why I use this workflow to solve my problem, but it works with mesh or sparse point cloud, not with dense. The algorithm works differently on dense cloud, and with no sense, I would like just It works as for the mesh or sparse cloud.

1.2.0 version practically put the psx as the main project file, and psz just to archiviate the project, but the psz doesn't save, for example, the "build Orthophoto" process results. Anyhow this procedure is not correlated to the file project type.

7
Bug Reports / Re: Dense cloud manual editing issue.
« on: December 15, 2015, 03:18:09 PM »
are you working in psz or psx?

Psx, but even with the version 1.1.6 I had similar problem to perform editing while I haven't any problem when I edit mesh.

8
Bug Reports / Re: Dense cloud manual editing issue.
« on: December 14, 2015, 07:43:19 PM »
Hello,
I've just installed 1.2.0 version. I'm trying to manually editing the dense cloud but the behaviour is really different from the manual editing applyed to the sparse cloud or to the mesh.

I start to explain.

If i want to edit manually a part of the mesh, I usually work on just a piece of it per time so I can avoid memory lack when I rotate, zoom or pan the model. I usually select a part of the mesh, I CROP the selection and then I start to remove from the selected part the unwanted mesh parts with the key DELETE SELECTION. When I've finihed, I just use the UNDO command until I have again the entire model, but all the previously unwanted part keep SELECTED: then I just delete such selected part and I start to edit another piece.

The same thing cannot be applied on the dense cloud unfortuantely: indeed when I use the key UNDO as before explained to go back to the entire dense cloud, photoscan select the entire cropped part at the beginning, and so I loose my editing.

May you correct such issue?

Thanks
Regards


Any answer?  :-\ :-\ :-\

9
Feature Requests / Re: Size of Marker ID text
« on: December 11, 2015, 09:15:33 PM »
Hello,
I would like to suggest one more thing about printed markers. I'm actually referring to the version 1.1.6 as I've not tried to do it on the 1.2.0, and I don't know if it has been changed in the new version. However...one of the most annoying thing is the limit of markers printed per single sheet: always SIX, whatever point size I choose. It's extremely paper consuming, it would be better to optimize the number of printed markersize based on the chosen marker size and paper size.

Thanks

10
Bug Reports / Re: Build orthomosaic issue in cluster mode
« on: November 28, 2015, 12:26:07 AM »
Hello Sebastiano,

The issue with the orthomosaic generation in network mode using planar projection will be also fixed in the next update.

Excelent!!
Thank you  ;D ;D

11
Bug Reports / Re: Build orthomosaic issue in cluster mode
« on: November 27, 2015, 10:23:31 PM »
Hello Alexey,
any news for me?

Thank you  in advance ;)

12
Bug Reports / Re: Build orthomosaic issue in cluster mode
« on: November 23, 2015, 09:57:09 PM »
Hello Alexey,
please find attached the pdf with all the followed step up to the orthomosaic building error above mentioned.

Hope this can help.


13
Bug Reports / Re: Build orthomosaic issue in cluster mode
« on: November 23, 2015, 07:44:04 PM »
BTW,
the marker detection step in network mode, even if the process has been completed, corrupts the project and makes it unreadable.

14
Bug Reports / Re: Build orthomosaic issue in cluster mode
« on: November 23, 2015, 06:21:50 PM »
Hello Sebas80,

Can you provide additional details on the orthomosaic generation settings, maybe a screenshot of the Build Orthomosaic dialog?

At the moment we are not able to reproduce the issue neither for mesh based, nor for DEM based orthomosaic generation.

So do other processing tasks work correctly for this project if performed using network mode?

Hello Alexey,
ok I'll try to replicate the error recording all the settings and I'll notify you as soon as I obtain the error.

Other network processes don't generate issues. Anyhow I'll try again all the steps from image allighment to orthomosaic generation in network mode.


15
Bug Reports / Re: Build orthomosaic issue in cluster mode
« on: November 22, 2015, 01:06:47 AM »
Hello Sebas80,

Thank you for reporting.

Have you checked if the named files are present in the given folder?

Hello Alexey,

Yes the file is immiediately created once the Orthomosaic building process starts within the path reported in my printscreen.

Pages: [1] 2 3