Forum

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Stunnline

Pages: [1]
1
Bug Reports / Re: Trackball/Calculation Coordinatesystem
« on: February 27, 2018, 04:16:50 PM »
.

2
Bug Reports / Re: Trackball/Calculation Coordinatesystem
« on: February 27, 2018, 04:15:56 PM »
Hello Alexey,

ahh, alright.
Pressing the update button after setting the accuracy does not do anything except resetting the view.
But if i align the photos again, it works :)
As you can see, the source data only contains the orientation of the camera relative to the drone.

Agisofts interpretation of Yaw, Pitch an Roll is another one. I already contacted Yuneec about that.
For a correct calculation i would need the absolute orientation of the camera, right?

3
Bug Reports / Re: Trackball/Calculation Coordinatesystem
« on: February 27, 2018, 12:43:09 PM »
Hey Alexey!

Thank you very much, it works now. As it seems the older Version of Agisoft did not import that data.
My Drone is only saving yaw, pitch and roll for the camera (without relation to the drone)
Do you have any suggestions, how i can use that data?

Best Regards.

4
Bug Reports / Re: Trackball/Calculation Coordinatesystem
« on: February 26, 2018, 02:41:49 PM »
Hey Alexey,

thank you for that quick answer!
You can download the reports from the old/new project file under the following link:
https://nextcloud.th-deg.de/s/fsMft1vh1WbsoXn
Sorry, the storage in the attachements is to low for the pdf files.

This problem also occurs on other, newer projects.

5
Bug Reports / Trackball/Calculation Coordinatesystem
« on: February 26, 2018, 02:21:34 PM »
Hello!

There is a new bug in version 1.4.0 ad 1.4.1, i think.
First of all: If i load my photos into photoscan and view them from the front by the shortcut, i get the image (1) you can see in the attachements. The photos are all in one plane, as they should be, because i shot them with the drone from a determinated altitude. But the alignment of the Trackball seems oddly off.
Shouldn't the trackballs blue line already be aligned with the level of the photos in this stage?

Well this wouldn't annoy me, but as it seems, this also interferes with the calculation. (Btw. I'm using WGS 84)
When the photos are aligned, the point cloud seems to be calculated right, but its orientation is not correct (2)
Also the calculated errors are too high. And now, when i view the model by for example front-shortcut again, the trackball is aligned, as it should be.

Is this a bug, or am doing something wrong?
This project with the exact same photos worked out in the older version (i think 1.3.5)

Thank you for your help!

6
General / Re: Export of Contour Lines
« on: February 26, 2018, 12:23:59 PM »
All i can say is, that the import into a CAD software isn't really possible.
Well it is possible, but it doesn't show anything except the 2D-view of the contour lines.
The DXF should contain 3D-Information, right?

7
General / Export of Contour Lines
« on: February 23, 2018, 11:52:57 AM »
Hi all!

i have a problem with the export options for the shapes (in this example contour lines)
I want to export my contour lines in a local coordinate system.(DXF) Unfortunately this setting isn't available, when exporting shapes. I calculated everything in WGS 84.
For Example the export of the Model or Pointcloud works fine to Local Coordinates.
When exporting those in the WGS 84 system, the models can't be represented correct, when opened with other software like CloudCompare.

I need to provide the contour lines for a customer, but the scaling and 3D-view of the contour lines doesn't work in his software, if exported in WGS 84.
Is there any possibility to fix this?

Thank you!

8
General / Re: smooth mesh in certain areas
« on: December 14, 2017, 06:15:53 PM »
Ok, tank you both!

9
General / Re: smooth mesh in certain areas
« on: December 13, 2017, 05:32:12 PM »
Ok, so it's not availaible in the pre-release, right?

Can you give me a rough date, when release 1.4.0 is going to start? :)

10
General / Re: smooth mesh in certain areas
« on: December 13, 2017, 12:15:05 PM »
Hey! Is the function mentioned above available now?

Pages: [1]