Messages

1

General / Disable edge “skirt”

« on: December 08, 2022, 06:51:29 AM »

Hi

I have a point cloud that’s pretty much 2.5d. I process it with metashape and it trys to figure out the edges which is not good for volumetric video. I want it to stop trying to process the edges, or stop trying to mesh where there aren’t enough points to make accurate mesh.

It has this kind of “skirt” around the whole edge of the mesh, if you look at the video it should be clear what I’m trying to remove.

Thanks for you help

2

General / Ply point cloud sequence, batch process meshing

« on: November 22, 2022, 07:07:07 PM »

Hi,

I have volumetric video that I’ve managed to get to the ply point cloud stage and I’m trying to push for the final  stage of meshing.

I can import 1 ply, reset region and then mesh and I get a good result.

Now what I need to do is automate a batch process where it goes through the other 1524 ply files (frames) and spits out the meshes.

Can anybody help?

Thanks

3

General / Re: Spotty Textures

« on: April 20, 2019, 12:12:43 AM »

Thanks for your help!

4

General / Re: Spotty Textures

« on: April 20, 2019, 12:07:49 AM »

Im not sure if the spots on the first picture are as visible to everyone else? They aren't supposed to be there at all.

5

General / Re: Spotty Textures

« on: April 20, 2019, 12:05:59 AM »

add

6

General / Spotty Textures

« on: April 20, 2019, 12:05:19 AM »

Hi,

I'm trying to scan this fireplace.

I have alignment settings at key:40000 tie:1000.

I am using a camera mounted ring light to take pictures, the light and lens are polarised and anything thats a little bit away from the camera has heavy shadows because the room is as dark as possible to control light.

When i reconstruct the photos it produces a good model but the texture is splotchy and spotted, mixed with the information retrieved from the shadowy parts of the picture.

If i mask out the shadow parts will it still be able to reconstruct?

7

General / Missing photos

« on: April 24, 2018, 07:11:14 PM »

Hi,

I've aligned my photos from a set i took in a turntable setup and half of them are missing (only 30). Photoscan used to have the manual marker setup but i can't find that on the current version.

what is the general process people use if camera won't be used?

p.s I'm aware this is a problem thats probably been raised here countless times before and i apologies for that but the search engine in the forum did yield anything (probably I'm using the wrong keywords) and 10 pages back of the general section i gave up.

8

Bug Reports / Re: display driver has stopped working and has recovered

« on: December 19, 2017, 01:54:08 AM »

2017-12-19 11:48:43 Depth reconstruction devices performance:
2017-12-19 11:48:43  - 100%    done by GeForce GTX 1070
2017-12-19 11:48:43 Total time: 7219.58 seconds
2017-12-19 11:48:43
2017-12-19 11:48:44 Generating dense point cloud...
2017-12-19 11:48:49 selected 91 cameras in 4.895 sec
2017-12-19 11:48:49 working volume: 9205x7293x6825
2017-12-19 11:48:49 tiles: 2x2x2
2017-12-19 11:48:49 selected 71 cameras in 0 sec
2017-12-19 11:48:49 preloading data...

And thats where the "display driver has stopped working and has recovered" message comes up.

9

Bug Reports / display driver has stopped working and has recovered

« on: December 17, 2017, 05:49:32 PM »

I have a geforce gtx 1070.

When i get to the building dense point cloud part of the ultra high dense cloud process the "display driver has stopped working and has recovered" message pops and photoscan closes.

Any idea why this is happening?