Forum

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - vdelpuerto

Pages: [1]
1
General / Re: Accuracy in Reference Geotagged images
« on: September 04, 2021, 08:10:32 PM »
Hi MK! Do you know why this should be done manually and not automatic like with ebee output?

2
General / Accuracy in Reference Geotagged images
« on: September 04, 2021, 05:15:47 PM »
Hi Alexey,

I am an ebee plus user and I never had any issues after exporting and aligning my geotagged images from PPK process in Emotion 3 (attach image with the accuracy in cm levels).

Now I started to use WingtraOne Gen II, but the results are very different. I geotagged the images with the ppk process in Wingtrahub, the exported and aligned them in Agisoft, but the accuracy marks 10 m in general, giving a general result of 1.6 m accuracy!!

Do you know why this could be? According the report in Wingtra Hub the ppk proccess end result is 0.03 m.


3
General / EIGEN-6C4
« on: September 03, 2020, 06:26:22 PM »
Hi everyone, I want to now if there is a dem for Agisoft to export models using the geoid EIGEN-6C4. I've been using the EGM 08 but i would like to try this other one.

Best regards

4
General / Re: Agisoft Beta Cloud
« on: July 22, 2020, 03:32:05 PM »
Hi Alexey,

I tried generating a mesh in the cloud with other project, and got the same error than the previous one.


5
General / Re: Agisoft Beta Cloud
« on: July 18, 2020, 05:46:05 PM »
Hi Alexey, any news?

6
General / Re: Agisoft Beta Cloud
« on: July 13, 2020, 10:30:12 PM »
Name of the project is "Primer Bloque.psx"

7
General / Re: Agisoft Beta Cloud
« on: July 13, 2020, 10:28:43 PM »
Hi Alexey,

here are the messages I receive

8
General / Re: Agisoft Beta Cloud
« on: July 10, 2020, 05:50:56 PM »
Hi Alexey.

Yes, that is the version installed.

9
General / Agisoft Beta Cloud
« on: July 02, 2020, 10:43:47 PM »
Hi everyone,

I'm trying to build a mesh of a project I have on the agisoft cloud. At 25-30 % of the process (8GB photos uploading) I get a message error and the process is aborted.

Any solution to this? I am not processing on my computer because I ran out of memory.

Best regards

10
General / Re: Discrepancies beetween Ortomosaic and Layers
« on: April 21, 2020, 01:34:55 AM »
Hi Alexey, not it works with your methos. Any idea why is this??

11
General / Discrepancies beetween Ortomosaic and Layers
« on: April 20, 2020, 07:13:05 PM »
Hi to all,

I am having issues exporting my data to open on gis software. I processed in WGS84 my survey, all the data, point cloud, dem, ortomosaic. After that I set a few points and polylines over the ortomosaic. Then I export the ortomosaic with the transformation of UTM 21S, same thing with the layers of the polylines and the points in SHP format and in DXF format. But when i open them in my GIS soft there is a discrepancy beetween both data. The ortomosaic does not match with my layers.

Any ideas what could i be doing wrong??

Best regards

12
General / Re: Processing UAV aerial images
« on: August 20, 2018, 04:04:46 PM »
Hello Alexey; thanks for replying. I will try this steps and adjustments. The only one I am not finding is the - generate mesh using visibility consistent (experimental) meshing method. I have the last version 1.4.3 agisoft installed.

13
General / Processing UAV aerial images
« on: August 17, 2018, 05:48:10 PM »
Dear community;

I would like to ask the next questions about processing to get better results, base on a data I recolected of a corridor mapping with an Ebee plus rtk activated. I recolected around 850 photos with 2.8 cm/px, 70 % lateral 60% longitudinal overlap.

Mi PC is a Intel Core I7-7740 X 4.30 GHz, 32 GB RAM, Windows 10 x64, Nvidia Gforce GTX 1060 6GB.

1) My first question is what could be the motive that my orthomosaic output is 3,44 cm/px when my flight was with 2,8 cm/px?

2) Is there any parameter in the process that I could set in my processing to correct the deformations in the outputs specially with the electric towers and its lines? (attach image)

3) If I want to get in my point cloud details of posts, towers, electric poles and other vertical elements beside the trees, what should be my parameters and sets in the flight to get this information?

4) Is there any way to get Agisoft classify medium and low vegetation such as crop fields to help me get a better DTM? I have some cropfields with around 60 cm to 1 m height that destortion my final DTM model.

5) How can I get a more soft 3d model? Some trees looks like buildings.

6) What is the recommended quality of process? MAX, HIGH or MEDIUM?

Here is the link for the attachments:

https://we.tl/t-6Ly0Tflfjl

Best Regards

Victor

Pages: [1]