Messages

1

General / Re: model not shown in correct elevation

« on: February 20, 2025, 12:15:04 PM »

Hi Paulo,

thank you.

Iam still a bit lost

the provided GeoID files in the link does not include the location I refer to , EPSG::32640 , the only available is as belwo
EGM2008 2.5' geoid model
WGS 84 (EPSG::4326) to EGM2008 height (EPSG::3855)
EGM2008 1' geoid model
WGS 84 (EPSG::4326) to EGM2008 height (EPSG::3855)

what do you advise in such case?

also, sorry, but what do you mean by CS?

thank you

2

General / Re: model not shown in correct elevation

« on: February 19, 2025, 11:25:13 AM »

Hi,, 

thank you, attached the file.

3

General / Re: model not shown in correct elevation

« on: February 18, 2025, 03:33:07 PM »

Hi again,

you have a valid point, I did not know what GeoID were before your reply.
basically I did brief research and found the file for the required place, however, it is only in .geo foramt. not .tiff file.
any advise?

4

General / model not shown in correct elevation

« on: February 13, 2025, 11:20:21 AM »

Hi all,

I tested with two models by uploading them to the cloud to share with my client, however, I noticed both of the models shows in correct geolocation, but not the correct elevation, they both shows way up high from the ground.

what could be the problem, they are both geo referenced with GCP and I choose the correct coordinate reference system.

please advise.

5

Agisoft Cloud / Re: I do not seem to figure it out

« on: October 03, 2024, 04:14:16 PM »

I really can not get to the best standards for processing my work and sharing it. 

6

Agisoft Cloud / Re: I do not seem to figure it out

« on: October 03, 2024, 04:13:02 PM »

Hi again, email sent.

but also I am seeing changes happening on the viewer finally. perhaps the result is not immediate and actually takes time to reflect and be viewable. but how is a one model taking me the whole day to have it online?

attached image FYI


on another hand, please advise: how can I upload only models ? currently there is a possibility to upload only tiled models, why I can not upload other formats for mesh models like the local viewer does?

7

Agisoft Cloud / Re: I do not seem to figure it out

« on: October 03, 2024, 03:21:50 PM »

Hi Alexy.

FYI, I am viewing within the account. not yet sharing a link.

but yes, the project is published, and the problem is presestant, I am unable to view the model.
attached photo

8

Agisoft Cloud / Re: I do not seem to figure it out

« on: October 03, 2024, 11:22:42 AM »

Hi Alexy

thank you for your prompt reply

the point cloud is geo referenced. I am able to view it only in local software. it is not viewable on the web viewer. attached a photo for your refrence.
I have additionally process a textured mesh and uploaded same as well. but not able to view anything

actually this is important for me. my main goal is to be able to upload the 3D models , not particularly the points clouds, because I want to share the models view\compare features with my clients. please advice.

9

Agisoft Cloud / I do not seem to figure it out

« on: October 02, 2024, 01:05:30 PM »

Hi all,

I had been a user for metshape since 2019. but I am finally experimenting the extra software and expanding y horizon.

I intend to experiment with the cloud but I do not seem to have any luck with it

let us try to look into one example together:
1- imported photos in software and ran alignment
2- upload model to cloud from file>cloud>upload
3- then choose to do point cloud from workflow>point cloud
4- agrees to cloud process
5- cloud process finish
6- point cloud shows in thumbnail in web but open in black screen
7- point cloud size nearly 5 GB on cloud


please advise

10

General / autodetecting my own custom targets

« on: September 21, 2024, 10:45:43 AM »

hi all,

for my projects, I use a custom printed GCP, they are standard for my team. is there a way that I can identify and autodetect these in the model?

11

General / Re: best format to share laserscans

« on: January 17, 2024, 04:16:39 PM »

Hi Alex,

thank you for your feedback.
I tried different .e57 files and it seems to work.

though one more question: how can I still have the GCP in the model without re-input individually?

12

General / Re: best format to share laserscans

« on: January 16, 2024, 03:02:23 PM »

for some reasons I can not import it into Metashape. any ideas?

13

General / best format to share laserscans

« on: January 16, 2024, 12:31:33 PM »

Hi all,

quick and short post.
I use Metashape as my main software for processing and manipulating 3D photogrammetric survey.
usually we hire 3rd parties to perform laserscanning for us on location (site survey)

my question:
I need the hired people to send me the 3D laser scans after they geo-reference them and process them in a format that I can still import in Metashape to process further products such as DEMs and orthomosaic, etc, as needed.
what should I ask them to do to ensure the data I receive is usable in such matter?

please advice.

14

General / Re: ERROR cannot open file

« on: July 13, 2023, 10:07:10 AM »

Hi again,

this was solved.
you were right about path length (character count) , I moved the file few levels up and opened it with no problems.

15

General / Re: ERROR cannot open file

« on: July 12, 2023, 07:07:41 PM »

Hi ,

thanks for the prompt reply

yes the file exists at the location

I tried opening it from location it failed, tried also the "open" from inside the software it also failed.