Messages

1

General / Re: Import 3D-Mesh after post processing

« on: March 18, 2021, 10:58:24 AM »

Today I tried it again and for some reason the script worked, if I put both models in a new created project.

Thanks for your help!

2

General / Re: Import 3D-Mesh after post processing

« on: March 17, 2021, 01:09:40 PM »

Hello,
Thanks for the answer.
I tried the script but it didn`t work. The edited model just disappered.
You can see the used parameters in th screenshot below.

3

General / Re: Import 3D-Mesh after post processing

« on: March 16, 2021, 11:07:14 AM »

Ok i know where I screwed up in Blender, I rotated the Mesh. Is there a way to fix this in Agisoft for example reallign it with markers?

4

General / Re: Import 3D-Mesh after post processing

« on: March 16, 2021, 09:39:04 AM »

Hello,
thanks for your answer.
They are not matching in Blender either.

5

General / Re: Import 3D-Mesh after post processing

« on: March 16, 2021, 12:34:43 AM »

Yeah, I dient do that so that is definetly not the problem.

6

General / Import 3D-Mesh after post processing

« on: March 15, 2021, 03:42:16 PM »

Hello,

I created a Mesh in Metashape out of drone pictures. After I processed it I exported it into Blender to clean up the Mesh.
Without noticing I screwed up the coordinate orientation in this step. Now I wanted to create the texture oft the Mesh in Metashape, which is not possible because the imported Mesh is not in the right position. Is there a way to orientate the Mesh again so I can create a texture.

Thank for your help!

7

General / Re: Allign camera pictures to laserscan data

« on: February 16, 2021, 11:39:58 AM »

There are 2 entries where both point clouds overlap so it wouldn´t be a problem to align the interior pointcloud to the exterior cloud

8

General / Allign camera pictures to laserscan data

« on: February 15, 2021, 04:11:34 PM »

Hello,

I´m working on a project where I´m supposed to build a 3D-Model of a castle.
So far I built a 3D-model of the outside based on UAV-pictures and of the inside based on scanning data. So far everything is fine. In the next step I want to take pictures of the inside to improve the texture of it.
Now I´m thinking that it might be a problem to get those pictures in the right position. Is there a way to do this in Agisoft?

Thanks for your help

9

General / Re: Combine UAV-Data with classic methods

« on: January 21, 2021, 05:12:40 PM »

Hello Alexey,
I have sent the data.

10

General / Re: Combine UAV-Data with classic methods

« on: January 21, 2021, 04:12:12 PM »

Hello Alexey,

yeah sure I can do that, where should I send it to?
I guess you need the pictures aswell?

Greetings

11

General / Re: Combine UAV-Data with classic methods

« on: January 21, 2021, 11:15:23 AM »

Hello Alexey,

thanks for your answer.
It still didn´t work. The calculated values of the new set markers are still wrong.
Should I also uncheck the GCPs I used before for the Image Alligment?

12

General / Combine UAV-Data with classic methods

« on: January 20, 2021, 01:29:07 PM »

Hello,

at the moment I struggle to combine UAV-survey measured data, with measured points outside of the flown area.
The Problem is that there is an offset from the calculated Points and the points I measured with classic methods (total station, GNSS...).
This means that the connection points doesn´t have the same coordinates.
I used a few of these connection points also as GCPs, is there a way to force the coordinates, measured with the total station, on the position of the GCPs in the point cloud or the orthomosaic?

Greetings

13

General / Exclude pictures with bad RTK-coordinates

« on: December 18, 2020, 04:58:15 PM »

Hello,
I have a project, where I flight with an ebeeX RTK drone. While taking some pictures the drone lost the RTK-signal or the signal was bad. Is there a way in Agisoft to exclude the coordinates of this pictures before Alignement?
If I use the RTK-coordinates of all pictures I get at some pictures an error of 4m.

Thanks for your help.
Greetings

14

General / Metashape edit mesh

« on: December 02, 2020, 04:22:44 PM »

Hi there,

im working on a project, where we took pictures of a castle wit a UAV and afterwards scanned some critical spots. After processing the UAV-pictures, I added the scan point cloud and build a mesh and a texture in Metashape. Now I struggle to optimize the mesh I tried a few software options, but I am not convinced of any yet.
Can you recommend any software.
PS: The goal is  to create a 3d-model with the textured mesh.

Thans for your help!