Messages

1

General / markers in the new version 2.0.1

« on: May 11, 2023, 05:05:01 PM »

Good evening everyone,

 Is it normal, that in the new version of Metashape, the flags of the markers are white? If I remember correctly, in the old version, they were blue

2

General / Re: Why this?

« on: January 28, 2020, 04:15:58 PM »

adjusted screen

3

General / Re: Why this?

« on: January 28, 2020, 04:15:20 PM »

Here initial screen

4

General / Why this?

« on: January 28, 2020, 01:51:39 PM »

Hi,
I have to create orthophotos from a series of cores.
the cores are inside a box shaped like a 1 meter long parellelepiped.
the point cloud of the box and the cardboard appears deformed by a curvature. why does this happen?
overlap of about 75%.



devo creare ortofoto di una serie di carotaggi.
i carotaggi sono all'interno di una scatola a forma di parellelepipedo di 1 metro di lunghezza.
la nuvola di punti della scatola e del cartaggio appaiono deformate da una curvatura. perchè accade questo?
sovrapposizione di circa il 75%.

5

General / how to create a point of origin?

« on: July 23, 2014, 01:00:55 PM »

I am photographing the surface of a series of concrete blocks in 3D, one by one.
How do I create a common origin for all models, with Agisoft?

I constructed a frame where emplace concrete brick, and then all the blocks are in the same position.

I would like to orient the surfaces of all the blocks in the same way between them, and give a zero point to the cloud of points (for example, the angle at the top left).

Is it possible? and if so, how?
thank you very much Stefano

6

General / Re: Camera Calibration Method & Parameters

« on: July 01, 2013, 01:01:00 PM »

very interesting! Could you explain better how to make this your idea?

7

General / Re: Problem with merged chunk

« on: April 23, 2013, 06:44:14 PM »

I tried to optimize, and after merging chunk error has risen to 97, while the georeferencing has worsened to 1.8 m

8

General / Re: Problem with merged chunk

« on: April 23, 2013, 06:35:54 PM »

I  just merged using the fact that they are already referenced in the same coordinate system.
Now i try to optimize.

9

General / Problem with merged chunk

« on: April 23, 2013, 06:24:55 PM »

I have two chunk
one with Reprojection error 1.2 and the oteher with r.err. 0.8

After aligning them with the geo-referencing and merged into a single chunk.
The Reprojection error flew to 80!
And the error of georeferencing has worsened considerably, from 18 cm to 90 cm.
Why? How can I avoid this problem?
0.9.1 build 1647 6a bit

10

General / Re: Agisoft PhotoScan 0.9.1 pre-release

« on: April 19, 2013, 02:01:04 PM »

Many thanks

11

General / Re: Agisoft PhotoScan 0.9.1 pre-release

« on: April 19, 2013, 01:28:15 PM »

Ciao!

codecs target, are useful only for GCP, or are used by the software as well as help in the process of alignment of the images?
Stefano

12

General / Re: Agisoft PhotoScan 0.9.1 pre-release

« on: April 09, 2013, 03:49:52 PM »

Many thanks now i try calibration separate
There aren't tree

13

General / Re: Agisoft PhotoScan 0.9.1 pre-release problem with mesh

« on: April 09, 2013, 03:12:40 PM »

after creating the mesh, I noticed the presence of these forms invented by the software .. someone has already happened?

14

Camera Calibration / Re: Can I calibrate from camera calibration certificate?

« on: February 27, 2013, 01:19:28 PM »

the other pages

15

Camera Calibration / Can I calibrate from camera calibration certificate?

« on: February 27, 2013, 01:18:40 PM »

If yes ... how should I do?
many thanks
Stefano