Forum

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Paulo

Pages: 1 ... 13 14 [15] 16 17 ... 87
211
Agisoft Cloud / Re: Unable to load project
« on: January 18, 2023, 07:07:27 PM »
Ilya,

I will try again and give you update....

and just got following error:

 Error: Can't perform curl, error code: 1

212
General / Re: Refine seam lines in Building Orthomosaic
« on: January 18, 2023, 05:27:32 PM »
Hello Alexey,

here is a general view of DTM used
then close up of ortho with many small islands
and same close up of DTM

213
Joseph,
how are you prcessing the data set? As a camera rig with visual cam as master or ?

214
Hello Joe,

nop your visual camera has a 1/1.7 inch format sensor with 12 Mpix, it should have something like 0.0019 mm pixel size...

215
Hello Joe,

from the thermal camera specs, the pixel pitch is 17 um or 0.017 mm so i Would suggest you enter this value in your thermal camera calibration Pixel size in Metashape and do a Optimize.. see if it improves...

216
General / Re: Manual entering of camera accuracy vs. marker accuracy
« on: January 17, 2023, 06:05:47 PM »
Hi Johannes,

I think you should manually input the correct camera accuracy (10 cm) and marker accuracy (2 cm) so their weight will be properly set in adjustment.

After that, just do a camera optimization and it should give a better result...

217
Agisoft Cloud / Re: Unable to load project
« on: January 17, 2023, 05:47:29 PM »
Dear Paul Pelletier,

Thank you for reporting the issue.

It seems like it is a rare issue that is not fixed in Metashape 1.8.4.

Please update Metashape to version 1.8.5 and try again, here is a link to the installer: https://s3-eu-west-1.amazonaws.com/download.agisoft.com/metashape-pro_1_8_5_x64.msi
Hello Ilya,

unfortunately I tried loading project to Cloud with 1.8.5 and still no luck... see attached log

218
General / Re: Refine seam lines in Building Orthomosaic
« on: January 16, 2023, 07:53:31 PM »
Any news on this issue?

219
Agisoft Cloud / Unable to load project
« on: January 15, 2023, 06:49:48 PM »
Hi all,

I have a project with 104 20 Mpix aligned fotos, depth maps and texturized model that I want to load to my account in Agisoft Cloud. It start to load images but after about 2% Metashape closes without any message and I must delete the lock to be able to open the project.

This happened many times.

Any help, please.
Code: [Select]
2023-01-15 09:43:03 Agisoft Metashape Professional Version: 1.8.4 build 14671 (64 bit)
2023-01-15 09:43:03 Platform: Windows
2023-01-15 09:43:03 CPU: Intel(R) Core(TM) i7-3630QM CPU @ 2.40GHz (laptop)
2023-01-15 09:43:03 CPU family: 6 model: 58 signature: 306A9h
2023-01-15 09:43:03 RAM: 16.0 GB
2023-01-15 09:43:04 OpenGL Vendor: NVIDIA Corporation
2023-01-15 09:43:04 OpenGL Renderer: GeForce GTX 670MX/PCIe/SSE2
2023-01-15 09:43:04 OpenGL Version: 4.6.0 NVIDIA 425.31
2023-01-15 09:43:04 Maximum Texture Size: 16384
2023-01-15 09:43:04 Quad Buffered Stereo: not enabled
2023-01-15 09:43:04 ARB_vertex_buffer_object: supported
2023-01-15 09:43:04 ARB_texture_non_power_of_two: supported
2023-01-15 09:43:29 LoadProject: path = C:/Users/paul.pelletier/Downloads/Mavic3/MiManzana.psx
2023-01-15 09:43:30 Loading project...
2023-01-15 09:43:30 loaded project in 0.078 sec
2023-01-15 09:43:30 Finished processing in 0.079 sec (exit code 1)

Update: after other upload attempt, Metashape exited once again with following log file attached...

220
Feature Requests / Redoing OrthoMosaic using exisying orthos
« on: January 12, 2023, 08:13:25 AM »
Sometime we want to redo an OrthoMosaic using different option but without need to redo individual image ortho.

Would be good to have an option to use existing orthos and thus avoid  to redo this part....

221
General / Refine seam lines in Building Orthomosaic
« on: January 12, 2023, 01:20:15 AM »
Hello all,

I have not been using the Refine seam lines in OrthoMosaicking but in my latest project (248 Vexcel 115 Mpix nadir images over an urban/industrial area), I tried it and got quite disappointing results.

First the processing increases greatly. It took some 68623.7 sec or some 19 hours to build Ortho. See attached log file....

Also the result is not great. While in some areas it does seem to avoid structures or buildings, in other areas ( in areas of lateral overlap) it creates a great amount of small seam lines islands that render the area blurry because of feathering. See 2nd attachment.

In current state this refine seamlines is not very useful as it leads to a lot of manual patching.

Hope the function will be improved as for now I will be using a competitor software for seam line refinement...

Update: I reran the orthomosaicking but this time without Refine Seamlines option. While process time is less the result is still not good with huge amoount of seamlines islands that render this result not usable, see 3rd attachment
Code: [Select]
2023-01-11 22:00:15 BuildOrthomosaic: projection = WGS 84 / UTM zone 14N +  GGM2010 geoid height, surface = DEM, blending mode = Mosaic, refine seamlines = 0, ghosting filter = 1, pixel size = 0.102685 x 0.102685
2023-01-11 22:00:15 Generating orthomosaic...
...
2023-01-12 04:51:35 Finished processing in 24679.5 sec (exit code 1)
please support help on this issue!

222
General / Re: Automated Mission Planning
« on: January 10, 2023, 10:27:40 AM »
Corensia,

Thanks for the info. Keep me posted! :)

223
General / Re: Usage of reference points as ground points
« on: January 09, 2023, 05:19:50 PM »
Hola agriflight,

if your ground RTK ground points are photo identifiable then marking them on the corresponding images would certainly help your alignment....

224
General / Automated Mission Planning
« on: January 05, 2023, 05:24:29 PM »
Hello all,

in Automated Mission Planning of User Manual it is said that mission can be exported in following formats:
Code: [Select]
Mission format
Specify mission formats from drop-down list. In Metashape available the following formats: DJI
Pilot, DJI WPML (WayPoint Markup Language) or Google Earth.

I would like to confirm if such DJI formats are compatible with Mavic 3 Enterprise running Pilot 2 app.

Thanks for any insights on this...


225
Python and Java API / Re: MS 2.0 script not working
« on: January 02, 2023, 06:37:50 PM »
Hi Maciek,
In v.2, point_cloud attribute has been changed to tie_points... please look at API reference manual.
For any further help adapting your scripts you can PM me.
In SA

Pages: 1 ... 13 14 [15] 16 17 ... 87