Messages

1

General / Process RTK data including GCPs

« on: May 13, 2025, 03:20:03 PM »

Hello,

I am new to RTK processing in Agisoft and have been following the tutorial available here:
https://agisoft.freshdesk.com/support/solutions/articles/31000161735-dji-with-rtk-coordinates-data-processing

Previously, when working without an RTK drone, I relied solely on GCPs. After alignment, I would uncheck the photos in the Reference pane and perform optimization using only the GCPs.

Now that I am working with RTK-enabled, accurately geotagged photos, I would like clarification on the recommended workflow:
Should I leave the photos checked along with the GCPs during the optimization step, or should I uncheck the photos and optimize using only the GCPs, as done in the non-RTK workflow?

I plan to use a 7-parameter adjustment for optimization and want to ensure I’m following best practices.

Thank you for your assistance! 

2

General / Optimize Camera Aligment for P4 Pro

« on: December 27, 2023, 08:17:31 PM »

Hey,

Could anyboyd pls advice me which settings to choose to optimize camera aligment for DJI Phantom 4 pro? and also for Mavic 3E?

Thanks

3

Feature Requests / Turn Off PC after Process is done

« on: July 30, 2018, 11:40:11 PM »

Please add this feature "Turn Off PC after Process is done" so i could leave my PC on for a night. After finishing BATCH process or any other process (e.g. Dense Cloud Generation) it will turn off PC automatically.

THX! 

4

Feature Requests / Shut down PC after JOB finished

« on: May 28, 2018, 12:19:40 AM »

Hello!

Please add SHUT DOWN PC after finish option. Sometimes I leave my PC on for a night to make DENSE CLOUD, it would be great feature to use!

Thanks!

5

General / Orthomosaic Is dark after export

« on: February 11, 2018, 05:28:12 PM »

Hello!

My Orthomosaic photo was dark, I made it bright in Agisoft software, but when I exported it stayed original Dark.

Why is it so?

6

General / Re: Dead Spots in DENSE CLOUD, pls HELP!

« on: February 10, 2018, 07:53:59 PM »

Thanks for reply!

I tried increasing points from 40.000 to 60.000 and ties from 4.000 to 6.000, the result were the same :\ any other suggestions?

I tried with different Software and worked fine, I just want to use Photoscan.

Cheers! 

7

General / Dead Spots in DENSE CLOUD, pls HELP!

« on: February 10, 2018, 01:22:16 PM »

Hello!

Currently I am working at big project. I have few problems, first when I Aligned Photos at Highest settings it only aligned 39/97. After several tries with THE SAME settings now I got 94/97 aligned photos. As you can see not all of them were aligned. After this process I created Dense Cloud at High settings, BUT there are dead spots under cameras (It wasn't taken into account) what is the problem? THANKS!

Please see attachment

8

General / Re: yaw, pitch and roll Information

« on: February 06, 2018, 12:21:11 PM »

Why my model is rotated?

9

General / Re: Improve Orthomosaic, HELP!

« on: February 06, 2018, 12:11:01 PM »

Thaanks I will try to do it 

10

General / Improve Orthomosaic, HELP!

« on: February 03, 2018, 03:23:13 PM »

Hello!

Could anybody pls tell me how to get rid of "Edges" in Orthomosaic??? How to make it smooth looking?

Have a look at attached Screens.

Thx! 

11

Feature Requests / Flight Planning App

« on: February 02, 2018, 03:48:10 PM »

Hello!

It would be great to have Flight Planning app from Agisoft, like Pix4D Capture or DroneDeploy. I use both apps, but they are unreliable and buggy.

So if Agisoft Team could make one of their own, it would be PERFECT!   

12

General / Re: yaw, pitch and roll Information

« on: February 02, 2018, 03:01:52 PM »

Thank you for your information!

Do you recommend me to ALWAYS enable this option? Will I have better results with it?

Also Should I turn on "Load Camera Location Accuracy from XMP meta Data" and "Load GPS/INS offset from XMP meta data"? what do they mean?

Regards 

13

General / yaw, pitch and roll Information

« on: February 02, 2018, 02:27:51 PM »

Hello!

Does Phantom 4 Pro record yaw, pitch and roll information in its photo? So When I import it in Agisoft Photoscan it will be shown there?

Currently I can not see this information. because of this, sometimes my model is rotated.

Please Have a look at my Screenshot.

14

Feature Requests / Re: Cross-section-based pointcloud editing

« on: November 02, 2017, 10:51:01 AM »

Great future to consider! I also want this future, I use additional software just for THIS feature.

15

Feature Requests / Assign shortcut keys for context menu items

« on: October 21, 2017, 06:31:10 PM »

Hello!

Please Add "Filter Photos By Marker" Button in GCP section. I need to right click every single GCP and than click on "Filter Photos By Marker" for my purposes. It must be so much easier to have button for that.

Thanks!