Forum

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - kiteman

Pages: 1 [2] 3 4 5
16
General / Problem with merged chunk
« on: April 23, 2013, 06:24:55 PM »
I have two chunk
one with Reprojection error 1.2 and the oteher with r.err. 0.8

After aligning them with the geo-referencing and merged into a single chunk.
The Reprojection error flew to 80!
And the error of georeferencing has worsened considerably, from 18 cm to 90 cm.
Why? How can I avoid this problem?
0.9.1 build 1647 6a bit

17
General / Re: Agisoft PhotoScan 0.9.1 pre-release
« on: April 19, 2013, 02:01:04 PM »
Many thanks

18
General / Re: Agisoft PhotoScan 0.9.1 pre-release
« on: April 19, 2013, 01:28:15 PM »
Ciao!

codecs target, are useful only for GCP, or are used by the software as well as help in the process of alignment of the images?
Stefano

19
General / Re: Agisoft PhotoScan 0.9.1 pre-release
« on: April 09, 2013, 03:49:52 PM »
Many thanks now i try calibration separate
There aren't tree

20
General / Re: Agisoft PhotoScan 0.9.1 pre-release problem with mesh
« on: April 09, 2013, 03:12:40 PM »
after creating the mesh, I noticed the presence of these forms invented by the software .. someone has already happened?

21
the other pages

22
Camera Calibration / Can I calibrate from camera calibration certificate?
« on: February 27, 2013, 01:18:40 PM »
If yes ... how should I do?
many thanks
Stefano

23
General / Re: relinking photos
« on: January 04, 2013, 07:38:13 PM »
many thanks

24
General / Re: relinking photos
« on: January 04, 2013, 07:18:26 PM »
I tried to use this method, but PhotoScan, can not open the project changed with 7zip.

Can anyone advise me another solution?

Best regards
Stefano

25
General / relinking photos
« on: January 04, 2013, 07:16:24 PM »
In an old post, Asmordean writes as follows:
If you've saved the project file (It'll be a .PSZ file) you can open it with 7Zip, it's a ZIP file.

Look for the "doc.xml" file.  Open it up in a text editor like Notepad++ or Notepad2.  The line <location path="filename.jpg" /> is what you're after.  You might be able to edit it to <location path="\\networkpc\directory\filename.jpg" />, though I've not tried that (no network at home).

If there are a lot of photos, use Search & Replace. Search for:
<location path="
Replace with:
<location path="newdirectory

After you edit it just put it back into the ZIP file (replace the old one).

I wouldn't mind seeing a "Save with photos" option.  It would be a huge file for some things but would make the PSZ 100% portable.

I found this when I was toying with structured light.   I take one with the projection and a second with just white light.  I align the structured light photos then edit the doc.xml file to replace all the photos with the white light ones and build the texture so I don't get all colour noise as a texture.  Works quite well, as long as you don't bump anything.

26
General / Re: orientation
« on: September 26, 2012, 01:06:43 PM »
many thanks, now i try.
Best regards

27
General / Re: info deselection
« on: September 26, 2012, 12:53:25 PM »
many thanks

28
General / orientation
« on: September 26, 2012, 12:46:56 PM »
In the absence of GCP, how can I change the orientation of my model?

29
General / info deselection
« on: September 26, 2012, 12:44:08 PM »
in a 3D model obtained with pS? It's possible deselect part of a selection?

30
General / Re: Agisoft PhotoScan 0.9.0 pre-release
« on: September 18, 2012, 05:03:09 PM »
Ok now I understand, excuse me
Stefano

Pages: 1 [2] 3 4 5